D2000 Product Data Sheet

Interpon D2000 GLOSS / SATIN / MATTE

Product Description

Interpon D2000 is a series of high durability powder coatings specifically formulated for use on architectural aluminum components. Conforming with the performance requirements of the AAMA2604.05 specification, Interpon D2000 gives superior exterior durability and color retention. Interpon D2000 powders are available in a 31 shade standard solid color range, as well as 15 metallic shades.

For more information on this product please contact us.

Powder Properties

Particle Size	Suitable for electrostatic spray
Specific Gravity	1.2-1.75 g/cm³ depending on color
Storage	Dry cool conditions below 75˚F
Shelf Life	12 months
Sales Code	Y Series
Stoving Schedule	20-50 minutes at 356˚F 15-35 minutes at 375˚F 10-25 minutes at 392˚F 8-15 minutes at 410˚F

Test Conditions

The results shown below are based on mechanical and chemical tests which (unless otherwise indicated) have been carried out under laboratory conditions and are given for guidance only. Actual product performance will depend upon the circumstances under which the product is used.

Substrate	Aluminum
Pretreatment	Chromate
Film Thickness	2.4 - 3.2 mils
Curing Schedule	15 minutes at 400˚F

Mechanical Tests

Dry Adhesion	AAMA2604-05, 7.4	Pass - Gt 0
Abrasion Resistance	AAMA2604-05, 7.6	Pass - Abrasion co-efficient > 20
Dry Film Hardness	AAMA2604-05, 7.3 ASTM3363	Pass - No rupture of film
Impact	AAMA2604-05, 7.5	Pass - No tape removal of film to substrate following 0.1" deformation

Chemical and Durability Tests

Salt Spray	AAMA2604-05, 7.8 ASTM B117	Pass at 3000 hours - No corrosion more than 1/32" - 1/16" from scribe Minimum blister rating 8
Constant Humidity	ASTM D2247 ASTM D714 AAMA2604-05, 7.8	Pass at 3000 hours - Blister formation less than "few" size no. 8
Wet Adhesion	AAMA2604-05, 7.4	Pass - No blistering, Gt 0
Muriatic acid Test	AAMA2604-05, 7.7	Pass - No blistering. Gt 0
Detergent Resistance	AAMA2604-05, 7.7	Pass - No blistering, no adhesion loss
Boiling Water Adhesion	AAMA2604-05, 7.4	Pass - No blistering, Gt 0
Exterior Durability	5yr Florida Exposure AAMA2604-05, 7.9 ASTM4214	Excellent performance. Color change ∆E (Hunter) <5. Gloss retention >30%. Chalking - None in excess of No. 8

Color Stability at elevated temperatures

Good

Nitric Acid Resistance

AAMA2604-05, 7.7

Pass - ∆E (Hunter) <5

Pretreatment

For maximum protection it is essential to pretreat components prior to the application of Interpon D2000. Aluminum components should receive a full multi-stage chromate conversion coating or suitable chrome-free pretreatment to clean and condition the substrate. Detailed advice should be sought from the pretreatment supplier.

Application

Interpon D2000 can be applied by manual or automatic electrostatic spray equipment. It is recommended that for consistent application and appearance product be fluidized during application. For solid shade, unused powder can be reclaimed using suitable equipment and recycled through the coating system. For mixed colors and certain special finishes, advice must be sought from the manufacturer as to the suitability or otherwise of the product for recycling. For all mixed color/special effect systems, advice must be sought as to the correct mixing ratio for virgin/reclaim powder. For application of the D-Series Architectural Products, the required Dry Film Thickness (DFT) is 2.4 - 4.5 mils, with no measurement below 1.8 mils.

Safety Precautions

This product is intended for use only by professional applicators in industrial environments and should not be used without reference to the relevant health and safety data sheet which AkzoNobel has provided to it's customer. If for any reason a copy of the relevant health and safety data sheet is not immediately available the user should contact AkzoNobel to obtain a copy before using the product. Minimum safety precautions in dealing with all powder coatings are as follows. All dusts are respiratory irritants. Therefore, inhalation of the dust or the vapors resulting from the cure should be avoided Take steps to prevent skin contact, but should contact occur, wash skin with soap and water. In case of eye contact flush immediately with clean water and seek medical advice. Dust clouds of any finely divided organic material can be ignited with an electric spark or open flame. Dust and powder should not be allowed to build up on surfaces or ledges. Dust collection equipment should be used which has provision for adequate explosion release. All equipment should be electrically earthed to prevent build up of static.

Disclaimer

The information given in this sheet is not intended to be exhaustive and any person using this product for any purpose other than that specifically recommended in this sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. While we endeavor to ensure that all advice we give about the product (whether in this sheet or otherwise) is correct we have no control over either the quality or condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing to do so , we do not accept any liability whatsoever or howsoever arising for the performance of the product or for any loss or damage (other than death or personal injury resulting from our negligence) arising out of the use of the product. The information contained in this sheet is liable to modification from time to time in the light of experience and our policy to continuous product development.

Akzo Nobel Website (opens in a new window)

Print

Printed from the Internet

PRODUCTS

INFO